Jump to content

E-gear initialization after clutch replacement


Alex_Leb
 Share

Recommended Posts

Hi everyone, i just bought my first 07 gallardo and now is time to replace the clutch. In my country there is no lamborghini dealer and now i found a mechanic who can replace the clutch, but as i can see from the manual after this i need to carry out the e-gear initialization. To do this my friend bring me the Lambo diagnostic computer with LaRa 7.0 installed but I don't know what to do. Does anyone know how to make E-gear initialization after clutch replacement ?

 

PLEASE HELP, i really need this...

 

Inside help files L140-Gallardo -LaraAS sistem.pdf and 04_E-gear_BasicSetting_ENG.pdf, i found few procedures:

 

1. For Clutch replacement: "4-Neutral Engagement -> 5-Hydraulic Circuit Discharge -> Removal of E-gear kit and transmission→clutch replacement→re-installation of transmission and E-gear kit -> 6 - Hydraulic Circuit Bleeding -> 5 - Hydraulic Circuit Discharge -> Oil level checkand top-up of oil in reservoir -> 1 - Clutch Kiss Point -> 2 - Grid Self Tuning -> 3 - Clutch Degradation Index reset"

 

2. For Replacement of E-gear kit: "4 - Neutral Engagement -> 5 - Hydraulic Circuit Discharge -> Replacement of E-gear kit -> 6 - Hydraulic Circuit Bleeding -> 5 - Hydraulic Circuit Discharge -> Oil level check and topup

of oil in reservoir -> 1 - Clutch Kiss Point -> 2 - Grid Self Tuning"

 

what procedure i should follow ?

 

 

Also i found the following scripts:

 

Bleading_Gallardo.dra (allows the clutch of e-gear vehicles to be bled)

E-gear_snap_new_Gallardo.dra (allows acquisition of the data in the e-gear control unit.)

Open_solenoid_Gallardo.dra (allows the e-gear system to be bled after the parts of the system that have to be replaced have actually been replaced)

Read_clutch_Gallardo.dra (reads the degree of clutch wear in e-gear cars

Read_write_clutch_Gallardo.dra (in e-gear cars, allows the initial clutch wear value to be written after the clutch has been replaced.)

Selflearning_egear_Gallardo (allows the e-gear system to be re-calibrated if the control unit or the entire system is replaced.)

Write_clutch_Gallardo.dra (in e-gear cars, allows the current clutch wear value to be written after the e-gear control unit has been replaced. The essential PIS have been inserted to improve car drivability)

 

Should i run them?

 

To replace clutch i ordered the following:

1 X 7L105269F CLUTCH/FLYWHEEL ASSEMBLY

1 X 86141671L CLUTCH RELEASE BEARING

1 X 7L105276 PILOT BEARING

1 X 86141297 CLUTCH POSITION SENSOR

1 X 7L103051A REAR MAIN SEAL

8 X WHT000938 MOUNTING SCREWS

3 X N10124306 MOUNTING SCREWS

1 X N90111302 O-RING

1 X WHT002218 O-RING

2 X TUTELA CS SPEED FLUID (LITER)

Share this post


Link to post
Share on other sites

Now when i opened the LaRa 7.0 i found only 5 predefined scripts (not like described in LaRa Manual what i wrote in my previous post):

 

Bleeding_Clutch_Gallardo.dra (E-gear bleeding CLUTCH)

Bleeding_Kit_Gallardo.dra (E-gear bleeding 2* step: Bleeding E-gear KIT)

egear_snap_NEW_gallardo.dra (E-gear Snap)

Filling_E-gear_Kit_Gallardo_MY04-08.dra (E-gear bleeding 1* step: Filling E-gear KIT)

Selflearning_Egear_gallardo.dra (E-gear Self Learning)

 

How can i do procedure for clutch replacement in LaRa 7.0:

"4-Neutral Engagement -> 5-Hydraulic Circuit Discharge -> Removal of E-gear kit and transmission→clutch replacement→re-installation of transmission and E-gear kit -> 6 - Hydraulic Circuit Bleeding -> 5 - Hydraulic Circuit Discharge -> Oil level checkand top-up of oil in reservoir -> 1 - Clutch Kiss Point -> 2 - Grid Self Tuning -> 3 - Clutch Degradation Index reset"

 

I'm completely confused and do not know what to do...

The nearest Lambo dealer in about 4500 km from me...

Share this post


Link to post
Share on other sites

  • 5 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

×
×
  • Create New...